Water repellent – oil repellent – anti-stain product protecting porous materials with a glossy ‘wet-look’ finish
ProtectGuard® Wet Look is designed to protect mineral porous building materials against water, oil and staining. It protects against the main causes of deterioration such as atmospheric pollution and grease-based stains. A surface treated with ProtectGuard® Wet Look will be easier to care for and will be protected over time. ProtectGuard® Wet Look gives treated substrates a glossy wet look’ finish that enhances the original colour. ProtectGuard® Wet Look allows the substrate to remain permeable to air and water vapour. It is UV-resistant and does not yellow.
ProtectGuard® Wet Look can be applied to vertical, horizontal, to all porous or very porous materials such as natural stone, terracotta, brick, concrete, limestone… ProtectGuard® Wet Look is used for new and renovated constructions..
  • Protects against water and oily liquids.
  • Anti-staining, anti-dirt.
  • Makes cleaning easier.
  • Lets a surface breathe.
  • UV-resistant, does not yellow.
  • Good resistance to abrasion.
  • Gives a glossy wet look finish.
  • Ready to use.
  • Non flammable.
Apply using a roller or a brush.
Clean tools and equipment immediately after use with water.
Apply the product to a surface that is clean, dust-free, grease-free and dry. To remove greasy stains use Guard Cleaner® Eco Soiled Floors. For efflorescence, laitance or concrete bloom use Guard Remover® Eco Efflorescence & Cement.
  • Use neat, do not dilute.
  • Shake the product well before use.
  • Always carry out a preliminary test.
  • ProtectGuard® Wet Look can be applied in 2 or 3 layers according to the glossy finish excepted.
  • Apply the 1st layer to the surface.
  • Let the product penetrate and dry (from 15 to 30 minutes according to the material’s porosity and temperature) then apply the 2nd layer.
  • To increase the glossy finish, it is possible to apply a 3rd layer after 30 min drying.
  • Do not over apply, eliminate any exceeding product before drying.
  • Drying time: 24 hours.
  • Optimum effectiveness obtained after 5 to 7 days.
  • Physical state at 20°C: Liquid.
  • Appearence: Milky.
  • Odour: None.
  • pH: 8.5 ± 0.5.
  • Boiling point [°C]: 100°C.
  • Density: 1.01 ± 0.01.
  • Solubility in water [vol/vol]: Total.
  • Flash point [°C]: Not applicable.
Coverage depends on the porosity of the material. The figures below should be used only as a general guideline: 6 to 10 m² / litre for 2 layers.
2 and 5 litres.
  • Keep in a dry place (between 5°C and 30°C).
  • Storage: 12 months following the production date when kept in the original unopened container.
  • Stubborn dirt should be cleaned off with clean water or with Guard Cleaner® Eco Soiled Floors diluted with 50% water.
  • Following traffic-induced wear, the protection and ‘wetlook’ can be regenerated by re-applying ProtectGuard® Wet Look diluted with 50% of water.
Environment-friendly product:
  • Water-based product.
  • Petroleum solvent and silicone free.
  • Non hazardous and non toxic.
  • Biodegradable > 80%*.
  • VOC = 52 g/l*.
  • Rating for VOC emissions into idoor air: B.
  • Remove all atmospheric pollution-related dirt from all surfaces to be treated before starting the treatment.
  • Always check the material’s porosity and carry out a test first to ensure the finished result is acceptable.
  • For best results it is essential that ProtectGuard® Wet Look is used when the temperature of the substrates is between 10°C and 30°C.
  • Do not apply during rain or in very hot weather. Air temperature between 5°C and 30°C.
  • For very porous materials apply a first impregnation layer (ProtectGuard® Wet Look diluted with 20 to 30% of water).
  • Do not mix with any other product.
  • In certain cases, the product can slightly modify the slipperiness of the surface, always carry out a preliminary test.
  • The intensity of «wet look» varies according to the nature of the material.
  • Do not apply to terracotta that has already been treated with wax, linseed oil...
  • Respiratory protection: Under normal conditions of use where adequate ventilation is available, no special respiratory protection equipment is needed.
  • Hand protection: Wear latex gloves.
  • Skin protection: No special protective clothing or skin protection is required under normal conditions of use.
  • Eye protection: If there is a real risk of splashing, wear protective goggles.
  • If swallowed: Do not induce vomiting. Contact a doctor or a specialist.
KEEP OUT OF THE REACH OF CHILDREN
Chemical nature:
Acrylic and fluor in aqueous phase.
GUARD INDUSTRIE (FRANCE)
Daniel Bruyat: Business Director
Phone: (+33) 65 84 46 13 73
Email: daniel.bruyat@guardindustrie.com
Website: www.guardindustrie.com     
 
NANO PHAM GROUP (VIET NAM)
Hotline: +84 918 244 844
Email: global@nanophamgroup.com
Website:
 

 

Important: The content of this documentation is based on our experience with the product. Guard Industry guarantees the quality of its products but expresslydisclaims all liability if the user does not follow the recommendations and conditions of use of the products, especially but not exclusively in the case of faultyapplication, application by untrained personnel, use of products not compatible with Guard Industry products, or adverse weather conditions For more information, consult the safety data sheet.
Accessing: 63
  • Ho Chi Minh
  • 97 Street No. 7, An Phu- An Khanh Urban Area, An Phu Ward (District 2), Thu Duc City, Ho Chi Minh City
  • Quang Ngai
  • 370 Nguyen Tu Tan Street, Tran Phu Ward, Quang Ngai City, Quang Ngai Province
  • Danang
  • K21/H2/1 Nguyen Van Hue Street, Thanh Khe Tay Ward, Thanh Khe District, Da Nang City
  • Thua Thien Hue
  • B08 The Manor Crown, To Huu Street, Hue City, Thua Thien Hue Province
  • Quang Binh
  • 37 Tran Kinh Street, Dong Hoi City, Quang Binh Province
  • Ha Tinh
  • 64 Le Thai To Street, Ky Thinh Commune, Ky Anh District, Ha Tinh Province
  • Thai Binh
  • 36A Quang Trung Street, Tran Hung Ward, Thai Binh Province
  • Thanh Hoa
  • 597 Street 1, Quang Hung Ward, Thanh Hoa City, Thanh Hoa Province
  • Hanoi
  • 99 Nhat Chieu Street, Nhat Tan Ward, Tay Ho District, Hanoi City
  • Hotline: 0918 244 844
  • Email:global@nanophamgroup.com
Total online: 1.159.436