Water, oil and stain repellent - anti-efflorescence specially formulated for fresh concrete.
  • ProtectGuard® FC 24H is a product that is designed to protect young and alkaline porous concrete (less than 28 days and ph > 9) against water, oil, stains, grime of all kinds, and graffiti.
  • ProtectGuard® FC 24H retards the deterioration of treated surfaces and simplifies their maintenance. It will reduce and can totally eliminate the appearance of efflorescence at a substrate’s surface.
  • Being water-based, ProtectGuard® FC 24H can be applied 24 hours after the concrete is poured on site or even as soon as fabricated elements are removed from the mould.
  • ProtectGuard® FC 24H impregnates the substrate without forming a film, so the substrate remains permeable to air and water vapour.
  • Once dry, ProtectGuard® FC 24H is colourless. It is available in flat or semi-gloss finish. It is also UV-resistant and does not yellow with time.
ProtectGuard® FC 24H is used outdoors on vertical porous alkaline surfaces such as concrete and young concrete (less than 28 days old).
  • Prevents penetration by water and greasy liquids.
  • Stain and grime repellent – limits soiling.
  • Limits greatly efflorescence.
  • Sacrificial anti-graffiti layer.
  • Limits frost damage.
  • Easy to clean.
  • Non-film forming – allows substrate to breathe.
  • UV-resistant, non-yellowing.
  • Ready to use and easy to use.
  • Non flammable.

 

Apply with a HVLP type spray gun or brush.

 
Clean tools and equipment immediately after use with water.
Apply the product to a surface that is clean, dustfree, grease-free and dry. To remove stains greasy stains use Guard Cleaner® Eco Soiled Floors. For efflorescence, laitance or concrete bloom use Guard Remover® Eco Efflorescence & Cement.
  • Use the product neat.
  • Shake the product using an electric stirrer for at least 1 min. until a homogeneous liquid is obtained.
  • Test first.
  • The substrate must be impregnated in a single coat.
  • Do not apply too thickly (maximum 150 g/m2).
  • Apply from bottom up.
  • Protect for 24 hours until dry.
  • Optimum effectiveness obtained after 5 to 7 days.
  • Physical state at 20°C: Liquid
  • Appearence: White
  • Odour: None
  • pH: 5.5 ± 0.5
  • Boiling point [°C]: 100°C
  • Density: 1.01 ± 0.02
  • Solubility in water [vol/vol]: Total
  • Flash point [°C]: Not applicable
Coverage depends on the porosity of the material. The figures below should be used only as a general guideline: 100 to 140 g/m2.
5 and 25 litres.
 
  • Keep in a dry place (between 5°C and 30°C).
  • Storage: 12 months following the production date when kept in the original unopened container.
Environment-friendly product:
  • Water-based product.
  • Petroleum solvent free.
  • Non hazardous and non toxic.
  • Biodegradable > 80%.
  • VOC < 30 g/l*.
  • Always clean off all atmospheric pollution and all concrete release agent from the surface before applying the product.
  • Do not dilute or mix with another product.
  • ProtectGuard® FC 24H may give a slight wet look to some concretes.
  • For ideal application and effective protection, ProtectGuard® FC 24H must only be used when the substrate temperature is between 10°C and 30°C. This product is incompatible with lower temperatures.
  • Do not apply during rain or in very hot weather. Air temperature between 5°C and 30°C.
  • Respiratory protection: Under normal conditions of use where adequate ventilation is available, no special respiratory protection equipment is needed.
  • Hand protection: Wear latex gloves.
  • Skin protection: No special protective clothing or skin protection is required under normal conditions of use.
  • Eye protection: If there is a real risk of splashing, wear protective goggles.
  • If swallowed: Do not induce vomiting. Contact a doctor or a specialist.
KEEP OUT OF THE REACH OF CHILDREN
Chemical nature
A blend of polymers in an aqueous phase.
GUARD INDUSTRIE (FRANCE)
Daniel Bruyat: Business Director
Phone: (+33) 65 84 46 13 73
Email: daniel.bruyat@guardindustrie.com
Website: www.guardindustrie.com     
 
NANO PHAM GROUP (VIET NAM)
Hotline: (+84) 918 244 844
Email: global@nanophamgroup.com
 
Important: The content of this documentation is based on our experience with the product. Guard Industry guarantees the quality of its products but expresslydisclaims all liability if the user does not follow the recommendations and conditions of use of the products, especially but not exclusively in the case of faultyapplication, application by untrained personnel, use of products not compatible
with Guard Industry products, or adverse weather conditions For more information, consult the safety data sheet.
Accessing: 256
  • Ho Chi Minh
  • 97 Street No. 7, An Phu- An Khanh Urban Area, An Phu Ward (District 2), Thu Duc City, Ho Chi Minh City
  • Quang Ngai
  • 370 Nguyen Tu Tan Street, Tran Phu Ward, Quang Ngai City, Quang Ngai Province
  • Danang
  • K21/H2/1 Nguyen Van Hue Street, Thanh Khe Tay Ward, Thanh Khe District, Da Nang City
  • Thua Thien Hue
  • B08 The Manor Crown, To Huu Street, Hue City, Thua Thien Hue Province
  • Quang Binh
  • 37 Tran Kinh Street, Dong Hoi City, Quang Binh Province
  • Ha Tinh
  • 64 Le Thai To Street, Ky Thinh Commune, Ky Anh District, Ha Tinh Province
  • Thai Binh
  • 36A Quang Trung Street, Tran Hung Ward, Thai Binh Province
  • Thanh Hoa
  • 597 Street 1, Quang Hung Ward, Thanh Hoa City, Thanh Hoa Province
  • Hanoi
  • 99 Nhat Chieu Street, Nhat Tan Ward, Tay Ho District, Hanoi City
  • Hotline: 0918 244 844
  • Email:global@nanophamgroup.com
Total online: 1.159.127